NSD VARICAM VS-5F Series Specifications And Instruction Manual Download Page 56

Page: 56 / 130

OPERATION

7. HOW TO USE BASIC FUNCTION

7-4. Turns ON the Power Supply

The VS-5F Series doesn’t have any power supply switch; therefore, use external switch for turning ON / OFF the
power supply.

Before turning ON the power supply, be sure that the wiring is correct and the screws of terminal block are
securely tightened.

The screen displays as below figure when turning ON the power supply for the first time after delivery.

After turning ON the power supply, the screen displays one second.

Changes the parameter setting (PRM) mode automatically.

The screen displays below figure when changing mode to the operation (RUN) mode or
switch setting (SET) mode.

In the case of restarting the power supply, keeps the mode just before turning OFF.

Operation (RUN) mode : RUN LED is ON

Switch setting (SET) mode : SET LED is ON

(1) (2) (3)
(1): Software specification (Displays 00.)
(2): Software version
(3): VARICAM model

：

VS-5F(-1)

：

VS-5FD(-1)

：

VS-5FX(-1)

Summary of Contents for VARICAM VS-5F Series



































































































































Search results

Summary of Contents for VARICAM VS-5F Series

Reviews:

Brands by name

Popular brands

NSD VARICAM VS-5F Series, Specifications And Instruction Manual

Search results

Summary of Contents for VARICAM VS-5F Series

Reviews:

Brands by name

Popular brands