NSD VARICAM VS-5F Series Specifications And Instruction Manual Download Page 105

Page: 105 / 130

OPERATION

10. HOW TO USE APPLIED FUNCTIONS (OPERATION MODE)

(4) Monitoring the rotation speed of ABSOCODER’s shaft

The rotation speed of ABSOCODER’s shaft can be check during the operation.

Name

Descriptions

①

SW / PRM display

When the rotation speed is displayed, the following figure is indicated.

②

DOG, PROGRAM

display

Displays the rotation speed.
The display unit is 1 r/min.
Indicates “1234 r/min” in the above display example.

③

MODE indicator

RUN LED is ON: Indicates the operation (RUN) mode.

④

RDY indicator

If there is no error, this indicator will turn ON when selecting the operation (RUN) mode.

This indicator is same condition as “System ready output signal” of the output connector.

③

①

④

②

Summary of Contents for VARICAM VS-5F Series



































































































































Search results

Summary of Contents for VARICAM VS-5F Series

Reviews:

Brands by name

Popular brands

NSD VARICAM VS-5F Series, Specifications And Instruction Manual

Search results

Summary of Contents for VARICAM VS-5F Series

Reviews:

Brands by name

Popular brands