manualshive.com logo in svg

NSD VARICAM VS-5F Series, Specifications And Instruction Manual

Share
Download
NSD VARICAM VS-5F Series Specifications And Instruction Manual Download Page 107

        

 

 

97 

 

OPERATION 

10. HOW TO USE APPLIED FUNCTIONS (OPERATION MODE) 

 

POINT 

*1: In the case of fine-adjusting the ON angle only, the operation after procedure 

⑦

  is not needed. 

   In the case of fine-adjusting the OFF angle only, the procedure 

④

, 

⑤

, and 

⑥

  are not needed. 

 

*2: Even if pressing POSITION 

  key or [CLR] key, changes the setting value monitoring mode of the switch output. 

 
 
*3: SW-ON LED and OFF LED switch when [ON / OFF] key is pressed every time. 
   Turns ON the SW-ON LED when fine-adjusting the ON angle. 
   Turns ON the OFF LED when fine-adjusting the OFF angle. 
 
 
*4: The ON angle cannot be adjusted more than the OFF angle.  Similarly, the OFF angle cannot be       
   adjusted more than ON angle.    Moreover, it cannot adjust in the range that prevents having overlaps to  
   anteroposterior dogs. 

 
 
 

⑦

  Turns ON the OFF LED. *3 

Presses [ON / OFF] key in order to   
fine-adjust the OFF angle.     
Turns ON the OFF LED.   

 

⑧

  Changes the fine-adjust mode. 

Presses 

  key of POSITION, and then the   

value blinks in the POSITION display area. 

 

⑨

  Fine-adjust the OFF angle value. *4 

Fine-adjusts the OFF angle value by 
pressing [+] or [-] key of POSITION. 
The value which is fine-adjusted is   
reflected the switch output. 

 

⑩

  Changes the setting value monitoring mode of the switch output. *2 

Presses [SET], and changes the setting   
value monitoring mode of the switch output. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Displays by 0.5

°

units 

Decimal point is ON : 0.5

°

 

Decimal point is OFF : 0.0

°

 

OFF LED 

is ON 

Summary of Contents for VARICAM VS-5F Series



































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands