15
Annunciate Trouble Indication
With this option box checked, the Console will announce three system
trouble conditions if they occur: Console low battery, sensor low battery,
and no sensor status. Sensor troubles type are announced followed by the
sensor zone number. The default is to
not
annunciate these conditions.
✓
NOTE FOR UL APPLICATIONS: UL requires the Annunciation Trouble
Indication option to be enabled (option box checked).
Annunciate Status with Home Button
A short press of the
HOME
button will cause the Console to announce
the Console’s time, current mode, and any trouble conditions. The default
for status annunciations is enabled. Optionally, status annunciations can
be disabled by un-checking this option box.
Annunciate Phone-Line/AC/Cell Module Status
If the telephone line is disconnected, or the AC power to the Console
fails, or the cellular module is off-line, the Console can annunciate these
conditions. These annunciations will clear when the condition is corrected.
The default sets these types of annunciations to
ANNUNCIATE ONCE
.
Alternately, use the this option to select
OFF
or
ANNUNCIATE EVERY
HOUR
. Regardless of this setting, the Console records the condition in
the event log and can report AC power failure to the Central Station (if
AC reporting is enabled).
✓
NOTE: To prevent disturbing the User, these annunciations will be
suppressed while the Console is in Night Mode
Clock Annunciation Format
Both 12-hour (AM/PM) and 24-hour (“military”) time formats are supported
in time announcements for Console status and reminder messages.
The default sets the time annunciations to
12-HOUR CLOCK
format.
Alternately, use the this option to select
24-HOUR CLOCK
format.
Data version
Displays the version number of the Console’s data for factory use and
troubleshooting.
Console Confi guration Misc.
Displays confi guration numbers of the Console for factory use and
troubleshooting.
CPU Identifi er
For factory use.
Temperature Limit Settings
The Console contains a built-in sensor that constantly monitors the room
temperature. The system can report and annunciate if the current room
temperature measured is higher or lower than programmed temperature
limits.
The Console will announce the high or low temperature alert every minute
until the room temperature is within the programmed acceptable limits.
The temperature limit alert is enabled by default. Select
DISABLE
to turn
off this feature or select
ENABLE HOME MODE ONLY
to sound and
report temperature alerts only while the Console is in Home Mode.
The default set-point for the low-temp alert is 40°F (4.4°C).
The default set-point for the high-temp alert is 90°F (32.2°C).
To change the temperature set-points, enter new values (in Fahrenheit)
into the
HI
G
H TEMP
and/or
LOW TEMP
fi ll-in fi elds.
A
TWO-WAY AUDIO
check box is available to select if a temperature alert
starts a Two-way audio session with the Central Station. The check box
is selected by default. Alternately, un-check this box to inhibit Two-way
audio after a temperature alert.
Language Selection
The Console can annunciate voice prompts in English or Spanish to
guide the User during operation, and guide the Dealer or Installer during
programming.
The two resident languages in the Console are English (EN) and
Spanish (ES).
Choose the active language for the Console using the
radio buttons in the Language Selection area.
To use a different language, the language vocabulary fi le must
fi rst be downloaded and installed in the Console’s fi rmware (See
Section 16.2).
Console Time Settings
The Console contains a built-in clock and calendar, and supports
automatic daylight saving time adjustment. The Console’s current time
and date setting and the daylight saving information is displayed on the
Console tab or the RA4200 software.
To change these settings, the Dealer or Installer should use the
CONSOLE TIME
function on the
COMMUNICATION
menu (or press the
CONSOLE TIME
icon on the toolbar ribbon). See Section 12.3.
✓
NOTE: If the UMTS-3
G
cellular module is installed, the Console’s time
will be set automatically over the air by the network.
Activity Windows
The activity timer is a feature that requires the User to press the Console’s
HOME
button or activate a activity reset transmitter during one or two
preset time windows to
prevent
an inactivity alarm from being reported.
Two activity time windows can be set by the Dealer or Installer. Each time
window can be enabled or disabled, and has a start and stop time.
• To enable
Activity Window 1
and/or
Activity Window 2
, check the enable
box next to the start and stop times.
• Set the start time for the activity window.
• Set the stop time for the activity window.
Night Mode
Night Mode is an option that will suspend all Console supervisory and
reminder annunciations during the Night Mode time window. This mode
allows the User to sleep without interruptions from the Console about
non-emergency conditions.
• To enable the
Night Mode
time window, check the enable box next to the
start and stop times.
• Set the start time for Night Mode.
• Set the stop time for Night Mode.
