manualshive.com logo in svg

Nokia Alcatel-Lucent OXO Connect Compact, Installation Manual

Share
Download
Nokia Alcatel-Lucent OXO Connect Compact Installation Manual Download Page 47

ZB

ZA

1

3

5

2

4

6

9

10

11

12

13

14

15

16

1

2

3

4

5

6

7

8

ANALOG INTERFACES

SLI16-2

ZB (5)

ZA (4)

Distribution panel  

or

4.2.6 Connection to the Public Network

4.2.6.1 Digital Public Network via T0 Access (or DLT0 Private Network)

The OXO Connect system can be installed near the digital network termination or at a certain distance
(up to 350 m), as required.

4.2.6.1.1 Connection without T0/S0 Forwarding

Distribution panel

DNT

Transmission

Reception

TX

RX

ISDN ACCESS - T0

1

2

3

4

5

6

7

8

BRA8-2

Caution:
In T0 Point-to-Point installations, the OXO Connect system MUST BE the terminating element of the bus
and any other terminating resistor MUST BE removed.

4.2.6.2 Digital Public Network by T1 or T2 Access

The diagram below shows a PRA-T2 board, but is equally applicable for a PRA-T1 board.

TX

RX

ISDN ACCESS - E1

PBX

NETW

PRA-T2

BUSY RAI

AIS

NOS CRC LOS

Distribution panel

DLT

Transmission

Reception

The PRA board is connected to a digital line termination (DLT) by 2 symmetrical twisted pairs.

Cable impedance: 120 Ohms +/- 20% between 200kHz and 1MHz; 120 Ohms +/- 10% at 1 MHz.

Chapter 

4

Powering and connecting the PBX to the customer LAN

8AL91217USAA - Ed. 01  - July 2018 - Installation Manual

47/216

Summary of Contents for Alcatel-Lucent OXO Connect Compact

























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands