manualshive.com logo in svg

Nokia Alcatel-Lucent OXO Connect Compact, Installation Manual

Share
Download
Nokia Alcatel-Lucent OXO Connect Compact Installation Manual Download Page 17

HIGH LEAKAGE CURRENT

Necessity to connect permanent earth before telecom access because of the high
leakage current (>3.5mA).

   

•

Fuse logo

Caution:
For continued protection against risk of fire, replace only with same type and rating of fuse.

Example: T 2,5AH / 250V

Type (T): Time Lag type

Current rating: 2,5A

Voltage rating: 250V

•

"WARNING" logo

 

Safety instructions to follow before installation or maintenance of the equipment.

Before installing this equipment you must read the installation documents due to elec-
tric shock Hazard.

The rear of panel and the front boards should only be removed by qualified mainte-
nance personnel.

Disconnect the mains cord before remaining the rear panel.

    

• Waste Electrical and Electronic Equipment (WEEE) logo

Chapter 

1

General presentation

8AL91217USAA - Ed. 01  - July 2018 - Installation Manual

17/216

Summary of Contents for Alcatel-Lucent OXO Connect Compact

























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands