manualshive.com logo in svg

Nokia Alcatel-Lucent OXO Connect Compact, Installation Manual

Share
Download
Nokia Alcatel-Lucent OXO Connect Compact Installation Manual Download Page 168

8 7 6 5 4 3 2 1

DAP RJ45 Socket

8=

7=

6=

5=

4=

3=

2=

1=

RTN (0 Volt) power

100 Base-T RX-

+48 Volt Power

+48 Volt power

100 Base-T RX +

100 Base- T TX-

100 Base-T TX+

RTN (0 Volt) power

Figure 8.21: Pin Layout Ethernet Connector RJ45 on the DAP

The  IP-DECT  base  station  access  points  are  fitted  with  2  LEDs  that  provide  information  about  the
status.

• Top LED – Yellow

This LED represents the status of the IP-DECT base station.

LED Status (Top LED, Yellow)

Meaning

Off

No power

0,5 sec. On - 0,5 sec. Off

Loading software/firmware

Short flash every 0,25 seconds

IP Network error (not connected, no DHCP/TFTP serv-
er, no DAP Controller

Fast blink

DAP operational, but trying to synchronize to another
DAP

Continuous fast blink

Hardware error

Steady On

DAP operational (and synchronized to other DAP or is
the synchronization master)

Note:

The colour of the top LED can be different depending on the operational mode.

•

Normal (single band) mode

In the normal single band mode, the top LED will be Yellow.

•

Dual Band

Mode In Dual Band mode, the LED colour shows the operational frequency:

•

Green: Europe/International

•

Red: North America / USA

• Lower LED – Red/Green

This LED is used to indicate the start-up and network status.

LED Status (lower LED, Red/Green)

Meaning

RED Steady on

Power but FPGA starting up

Chapter 

8

Device commissioning

8AL91217USAA - Ed. 01  - July 2018 - Installation Manual

168/216

Summary of Contents for Alcatel-Lucent OXO Connect Compact

























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands