Newland NLS-EM20-EX User Manual Download Page 93

Page: 93 / 187

Startup settings

Coupon

UPC-A/EAN-13 With Coupon Extension code

UPC-A with EAN-13 Two symbologies can be attached Coupon Extension code.

Coupon Have 3 Types of composition:

•

To 5 The beginning UPC-A + GS1-128

•

To 5 The beginning UPC-A + GS1 Databar

•

To 99 The beginning EAN-13 + GS1-128

The latter part is called Coupon Extension.

When set to

shut down

When UPC-A , EAN-13 , UCC/EAN-128 , GS1 Databar If enabled, the previous part UPC-A or EAN-13 still

Can be read.

When set to

Allow connection

There are two possible situations: 1 , If you read the two parts before and after, just output two; 2 If only one of the two is available, only one will be output.

When set to

Must be connected

When the two parts are read, there will be output.

* * 【shut down】

[Allow connection]

[Must connect]

Exit settings

Summary of Contents for NLS-EM20-EX




























































































































































































Search results

Summary of Contents for NLS-EM20-EX

Reviews:

Related manuals for NLS-EM20-EX

Brands by name

Popular brands

Newland NLS-EM20-EX, User Manual

Search results

Summary of Contents for NLS-EM20-EX

Reviews:

Related manuals for NLS-EM20-EX

Brands by name

Popular brands