Newland NLS-EM20-EX User Manual Download Page 128

Page: 128 / 187

Startup settings

Rectangular code

Rectangular code, here specifically refers to rectangular Data Matrix Barcode.

Data Matrix There are two formats for barcodes:

•

Square code with the same number of length and width modules: 10*10 , 12*12....144*144 .

•

Rectangular codes with inconsistent length and width modules: 6*16 , 6*14...14*22 .

* *

【Enable】

【Prohibited】

Data Matrix Inverted

Data Matrix There are positive and reverse barcodes.

Normal phase bar code: bar code with light background and dark bar

Inverted barcode: dark-colored bottom, light-colored barcode

* * [Only identify the normal phase barcode]

[Only recognize reverse barcode]

[Recognize both positive and negative barcodes]

118

Summary of Contents for NLS-EM20-EX




























































































































































































Search results

Summary of Contents for NLS-EM20-EX

Reviews:

Related manuals for NLS-EM20-EX

Brands by name

Popular brands

Newland NLS-EM20-EX, User Manual

Search results

Summary of Contents for NLS-EM20-EX

Reviews:

Related manuals for NLS-EM20-EX

Brands by name

Popular brands