manualshive.com logo in svg

NetApp SG100, Hardware Installation And Maintenance Manual

Share
Download
NetApp SG100 Hardware Installation And Maintenance Manual Download Page 83

•

Look for a lit blue identify LED on the front or rear of the controller.

The front identify LED is behind the controller front bezel and might be difficult to see if
the bezel is installed.

•

Check the tags attached to the front of each controller for a matching part number.

2. Remove the controller front bezel, if one is installed, to access the front panel controls and

indicators.

3. Optional: Turn off the blue identify LED if you used it to locate the controller.

•

Press the identify LED switch on the controller front panel.

•

Use the controller BMC interface.

Turning the controller identify LED on and off

 on page 81

Replacing the services appliance

You might need to replace the appliance if it is not functioning optimally or if it has failed.

Before you begin

•

You have a replacement appliance with the same part number as the appliance you are
replacing.

•

You have labels to identify each cable that is connected to the appliance.

•

You have physically located the appliance that you are replacing in the data center.

Locating the controller in a data center

 on page 82

•

The appliance has been placed maintenance mode.

Placing an appliance into maintenance mode

 on page 78

About this task

The StorageGRID node will not be accessible while you replace the appliance. If the appliance is
functioning sufficiently, you can perform a controlled shutdown at the start of this procedure.

Note: If you are replacing the appliance before installing StorageGRID software, you might not
be able to access the StorageGRID Appliance Installer immediately after completing this
procedure. While you can access the StorageGRID Appliance Installer from other hosts on the
same subnet as the appliance, you cannot access it from hosts on other subnets. This condition
should resolve itself within 15 minutes (when any ARP cache entries for the original appliance
time out), or you can clear the condition immediately by purging any old ARP cache entries
manually from the local router or gateway.

Steps

1. When the appliance has been placed maintenance mode, shut down the appliance.

Hardware Installation and Maintenance Guide for SG100 and SG1000 Appliances 

83

Maintaining the appliance

Summary of Contents for SG100







































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands