manualshive.com logo in svg

NetApp SG100, Hardware Installation And Maintenance Manual

Share
Download
NetApp SG100 Hardware Installation And Maintenance Manual Download Page 24

Port

Type of port

Function

3

Admin Network port on the
appliance (labelled P1 in the
figures)

1-GbE (RJ-45)

Attention:
This port
operates only
at 1000
baseT/full
and does not
support 10-
or 100-
megabit
speeds.

Connects the appliance to the Admin
Network for StorageGRID.

Rightmost RJ-45 port on the
appliance

1-GbE (RJ-45)

Attention:
This port
operates only
at 1000
baseT/full
and does not
support 10-
or 100-
megabit
speeds.

•

Can be bonded with management port 1
if you want a redundant connection to
the Admin Network.

•

Can be left disconnected and available
for temporary local access (IP
169.254.0.1).

•

During installation, can be used to
connect the appliance to a service laptop
if DHCP-assigned IP addresses are not
available.

Steps

1. Connect the BMC management port on the appliance to the management network, using an

Ethernet cable.

Although this connection is optional, it is recommended to facilitate support.

2. Connect the network ports on the appliance to the appropriate network switches, using TwinAx

cables or optical cables and transceivers.

Note: The four network ports must use the same link speed. See the following tables for the
equipment required based on your hardware and link speed.

SG100 link speed (GbE)

Required equipment

10

SFP+ transceiver

25

SFP28 transceiver

SG1000 link speed (GbE)

Required equipment

10

QSA and SFP+ transceiver

25

QSA and SFP28 transceiver

40

QSFP+ transceiver

100

QFSP28 transceiver

•

If you plan to use Fixed port bond mode (default), connect the ports to the StorageGRID
Grid and Client Networks, as shown in the table.

Hardware Installation and Maintenance Guide for SG100 and SG1000 Appliances 

24

Installing the hardware

Summary of Contents for SG100







































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands