NEC T30A User Manual Download Page 61

Page: 61 / 252

-34-

Table 4-1 Library Status displayed in the Operation Panel

Message

Description

PLEASE INSERT MAGAZINE

Magazine insertion is requested.

MAGAZINE UNLOCKED

Magazine is not locked.

PLEASE CLOSE I/O STATION

I/O Station CLOSE is requested.

INITIALIZING

･･･

Initialization is in progress.

INVENTORY

･･･

Inventory is in progress.

SETTING

･･･

Setting in progress

** CHK **
[XXXX]

Library error status (xxxx is the CHK code)

RECOVERING

･･･

PLEASE WAIT

Library firmware is in recovery.

LIBRARY FIRMWARE
UPDATING!

Library firmware update is in progress.

DRIVEn FIRMWARE
UPDATING!

Drive firmware update is in progress.

DRIVE DUMP DATA
UPLOADING!

Dump data is being uploaded from drive.

EXCHANGE SLOTFULL

A cartridge is stored in the exchange slot.

CARTRIDGE WRONG
INSERTION

A cartridge has been incorrectly inserted in the drive.

ENDURANCE
COUNT OVER

The number of Accessor mechanism operations has reached
the expected life (endurance) value

OFFLINE

Library Offline(Not Ready)

CLEANING...

During drive cleaning
(This status message is displayed in doing “Clean Drive”)

REPLACE CLEANING MEDIA

Replacement of cleaning cartridge

CLEAN DRIVEn

Drive n cleaning is requested

PSU n FAULT

Power module error

PSU n FAN ERROR

Power module fan error

REDUNDANT PSU ERROR

Redundant power module error

Drive n FAN ERROR

Drive FAN error

READY

Ready(Idle)

2. Accessor status display section

Indicates whether a cartridge tape exists in the picker section of the accessor.

Figure 4-3 Accessor Icon

(With no cartridge tape)

(with cartridge tape)

Summary of Contents for T30A





























































































































































































































































Search results

Summary of Contents for T30A

Reviews:

Related manuals for T30A

Brands by name

Popular brands

NEC T30A, User Manual

Search results

Summary of Contents for T30A

Reviews:

Related manuals for T30A

Brands by name

Popular brands