NEC T30A User Manual Download Page 199

Page: 199 / 252

-172-

Remove the front bezel of the magazine operating panel.

Remove it by pushing the left lock.

Unfasten the controller board screw and pull the controller board towards you.

Replace the controller board with a new one, fasten the screw, and then mount the front bezel and

rack ear L using the opposite procedure to the procedure used to demount them.

Turn on the power to the library.

10.

Fault LED lights up after turn on the power to the library, and it is displayed on an operator panel
as "UNMATCHED MAINT DATA ERROR."

11.

Restore the maintenance information, referring to "10.1.2 Restoring Maintenance Information".

12.

Since it is displayed as Unit information was restored successful, turn off and turn on the power
supply of a library.

13.

Perform library diagnostics, referring to "9.2

Diagnosis test

Screw

Summary of Contents for T30A





























































































































































































































































Search results

Summary of Contents for T30A

Reviews:

Related manuals for T30A

Brands by name

Popular brands

NEC T30A, User Manual

Search results

Summary of Contents for T30A

Reviews:

Related manuals for T30A

Brands by name

Popular brands