NEC T30A User Manual Download Page 82

Page: 82 / 252

-55-

4.4.4.3

Statistics

This menu is used to check the statistics information in Library.

Table 4-27 Information to be displayed on Statistics

Submenu item

Description

View Accessor Data

This checks the statistics information in the Accessor.

View Retry Data

This checks the statistics information in the Retry.

View Error Data

This checks the statistics information in the Error.

Clear Accessor Data

This clears the statistics information in the Accessor.

Clear Retry Data

This clears the statistics information in the Retry.

Clear Error Data

This clears the statistics information in the Error.

4.4.4.4

Telnet Service Port

This menu is used to enable and disable the TELNET port.

4.4.4.5

View Revision

This menu is used to check the firmware revision of the library and the installed drive.This menu is

used to check the firmware revision information of Library.

Table 4-28 Information to be displayed on View Revision

Submenu item

Description

Library

vendor ID / product ID / Serial No / FW rev / mac address

Drive

vendor ID / product ID / serial No / FW rev / wwnodename /
wwportname

4.4.4.6

Drive Replacement

This menu is used to exchange the drive.

Submenu item

Description

Selection of the drive

Remove Drive
  This is used to remove drive.

Restore Drive
  This is used to restore drive.
  It is chosen whether a drive serial number is succeeded after Restore
Drive selection.

Summary of Contents for T30A





























































































































































































































































Search results

Summary of Contents for T30A

Reviews:

Related manuals for T30A

Brands by name

Popular brands

NEC T30A, User Manual

Search results

Summary of Contents for T30A

Reviews:

Related manuals for T30A

Brands by name

Popular brands