NEC T30A User Manual Download Page 30 | Manualshive

Page: 30 / 252

background image

-3-

1.3.2

Operator panel

The operator panel has LEDs that indicate the status of the library, an LCD panel that displays the

library status, operations, messages, library settings, error messages, etc., and buttons used to operate the
library.

Figure 1-2 Operator panel

1.3.2.1

Status LED

The following four LEDs are included in the operation panel.

Table 1-1 Status LED on OperatorPanel

Ready indicator
This Green LED is on when library is ready state to the host.
On :Ready
Blinking :

Library being initialized or an inventory is being taken

:The accessor moves by the command from the host/WEB/operator panel

: Initialize the drive / Diagnosing / Magazine is opend / Library is offline state.

Drive cleaning indicator
Lighting:The drive is requesting cleaning.
Blinking:The drive is being cleaned.

Cartridge error indicator
Lighting

：

This Orange LED is on when the cartridge error has been detected.

                        When SCD=6/7/J is reported in cartridge Load to Drive.
                        When Cleaning cartridge is used 50 times or more.
  Turning off method:Magazine opening and shutting
  Attention:After  it  is  opened  and  shut,this  LED  doesn’t  light  even  if  the  cartridge  judged  to  be

abnormal before is turned on again in the magazine. (similar in case of I/O station)

Library error indicator
  Lighting:This Orange LED in on when drive or accessor error has been detected.
  Blinking:The library has recovered from error.
  Turning off method:After the library has recovered(Blinking),please execute a warning off from

operator panel.(refer to 4.4.1)

«
...
28
29
30
31
32
...
»

Summary of Contents for T30A





























































































































































































































































Reviews:

No comments

Related manuals for T30A

Brand: Euromate Pages: 23

Brand: Tab Pages: 26

Brand: Morrow Pages: 46

Brand: U-Line Pages: 39

Brand: IBM Pages: 295

Brand: Holzmann Pages: 20

DLT-V4 EZ-Kit Series

Brand: Freecom Pages: 2

CHEETAH NS 10K.2 ST3450802SS

Brand: Seagate Pages: 80

Brand: Broadcom Pages: 24

Brand: DURHAND Pages: 16

Brand: Cavalry Pages: 20

CADA-U32A Series

Brand: Cavalry Pages: 20

Brand: Beta Pages: 7

Neutrino SK-2500

Brand: Akitio Pages: 8

Brand: Arcserve Pages: 18

Grass Valley K2 ASI Media Client

Brand: THOMSON Pages: 2

Brand: Holzstar Pages: 13

Hercules HC1020PCW15

Brand: KING CANOPY Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands