NCR 6003-K001-V003 Installation Instructions Manual Download Page 134 | Manualshive

Page: 134 / 163

background image

120

Figure 217

28)

Repeat steps 18) – 19) and 22) - 27) (routing & placement of printer cables and
printer ground wire) for the printer located on the B-Side of the dispenser using
three more provided cable ties (006-8616073) and one more provided cable clamp
(006-8611458).

Note: On the B-Side, the printer ground wire does not have to be routed up and over
the inner top of the dispenser since the heater is on the opposite A-Side. For the B-
side printer, the printer ground wire can be bundled with the loop of printer cables
that already are being tucked away up under the APC module (identified previously in
Figure 217).
29)

Disconnect the AC power cable that is attached to the power supply connector
without the Invenco Link attached. See Figure 218 below.

«
...
132
133
134
135
136
...
»

Summary of Contents for 6003-K001-V003




































































































































































Reviews:

No comments

Related manuals for 6003-K001-V003

Brand: Landoll Pages: 83

Brand: Panasonic Pages: 174

Brand: Haki Pages: 24

Brand: Dakota Digital Pages: 5

Brand: Danelec Pages: 67

Brand: Danfoss Pages: 106

Brand: Jackco Pages: 6

Brand: Federal Signal Corporation Pages: 12

Brand: IEMCA Pages: 82

KID 80-IV Touch

Brand: IEMCA Pages: 122

Brand: Calrec Pages: 92

Brand: T&D Pages: 28

Brand: Teac Pages: 9

Brand: Tascam Pages: 3

Brand: Tascam Pages: 56

Portastudio 2488

Brand: Tascam Pages: 28

Brand: Tascam Pages: 2

Brand: Tascam Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands