NCR 6003-K001-V003 Installation Instructions Manual Download Page 64 | Manualshive

Page: 64 / 163

background image

50

Figure 87

41)

Feed excess cabling into the electronics cavity so that the majority of the cables'
slack will be placed inside of the Dispenser Head. Re-use any existing cable
restraints that may be present. It may be necessary to use zip-ties or additional
cable restraints to secure the loose wiring. These must be provided by the installer.

Caution: After all cables are reconnected, double check that no cables are hanging or
lying in front of the heater exit. Any remaining cables hanging in front of the heater or
lying in front of the heater exit should be re-routed and restrained using one of the
additional supplied cable ties (006-8616073).

Warning:

Heater surfaces are hot! Do not touch!

42)

Re-secure all loose wires such that they do not interfere with closing any panels.

43)

All wires are to be routed away from any sharp edges and door joints/gaskets.

44)

The following steps are to be performed ONLY on the B side of the dispenser.
a)

Push up and Re-fasten the Money/Volume Display Assembly to the Dispenser
Frame. See Figure 88

«
...
62
63
64
65
66
...
»

Summary of Contents for 6003-K001-V003




































































































































































Reviews:

No comments

Related manuals for 6003-K001-V003

Brand: ABB Pages: 18

Brand: R-Tech Pages: 3

Brand: Jackco Pages: 6

The Wave Transformer

Brand: EarthQuaker Devices Pages: 21

Brand: M-system Pages: 3

Brand: M-system Pages: 5

Brand: MA Pages: 2

Brand: NanoVibronix Pages: 2

Brand: NanoVibronix Pages: 32

Shapes Hexagons

Brand: Nanoleaf Pages: 27

Marathon Multi600

Brand: Saeyang Pages: 21

Brand: S&C Pages: 11

Brand: VDO Pages: 15

Brand: VDO Pages: 20

Brand: ValueStore US Pages: 2

Littmann Classic II Pediatric

Brand: 3M Pages: 53

Brand: Opvimus Pages: 50

Brand: popular Pages: 27

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands