NCR 6003-K001-V003 Installation Instructions Manual Download Page 109

Page: 109 / 163

Figure 171

Figure 172

Caution: After all cables are reconnected, double check that no cables are hanging or
lying in front of the heater exit.

Warning:

Heater surfaces are hot! Do not touch!

11)

Any remaining cables hanging in front of the heater or lying in front of the heater
exit should be re-routed and restrained using one of the additional supplied cable
ties (006-8616073).

12)

All wires are to be routed away from any sharp edges and door joints/gaskets.

13)

Lock and close the outer dispenser housing using the appropriate key and / or
security torx driver. See Figure 173.

Summary of Contents for 6003-K001-V003




































































































































































Search results

Summary of Contents for 6003-K001-V003

Reviews:

Related manuals for 6003-K001-V003

Brands by name

Popular brands

NCR 6003-K001-V003, Installation Instructions Manual

Search results

Summary of Contents for 6003-K001-V003

Reviews:

Related manuals for 6003-K001-V003

Brands by name

Popular brands