NCR 6003-K001-V003 Installation Instructions Manual Download

Page: 88 / 163

Figure 131

Caution: After all cables are reconnected, double check that no cables are hanging or
lying in front of the heater exit.
14)

Any remaining cables hanging in front of the heater or lying in front of the heater
exit should be re-routed and restrained using one of the additional supplied cable
ties (006-8616073).

Warning:

Heater surfaces are hot! Do not touch!

15)

All wires are to be routed away from any sharp edges and door joints/gaskets.

16)

Close the OPTIC door

17)

Use the TPX88 Tokheim key to lock the OPTIC door after ensuring that all cables

are secured behind the OPTIC unit.

Summary of Contents for 6003-K001-V003




































































































































































Search results

Summary of Contents for 6003-K001-V003

Reviews:

Related manuals for 6003-K001-V003

Brands by name

Popular brands

NCR 6003-K001-V003, Installation Instructions Manual

Search results

Summary of Contents for 6003-K001-V003

Reviews:

Related manuals for 6003-K001-V003

Brands by name

Popular brands