NCR 6003-K001-V003 Installation Instructions Manual Download Page 20 | Manualshive

Page: 20 / 163

background image

6

WAYNE VISTA DISPENSER

1)

Locate Side B of the dispenser.

Note: For the purposes of this procedure, Side B of the dispenser refers to the side
without the manufacturer’s label/Serial Number Plate.
Note: References to “left-hand” and “right-hand” are as viewed into the pump on the
Side the installer is working on.
2)

Use a Wayne Security Key to unscrew the two security bolts (Figure 2) at the top left
and top right of the electronics head bezel.

Figure 2

3)

Lower the electronics head bezel by pulling the top forward until it fully rests on the
suspension cables.

4)

Acquire the heater (NCR heater assembly) and OPTIC heater wire guard (497-
0522796).

Note: For Vista, the power supply bracket can remain mounted to the inner dispenser
wall during installation of the heater in the following steps, even though the pictures
below do show the power supply bracket removed from the dispenser during heater
installation.
5)

Slide the wire guard (497-0522796) around the NCR heater assembly so that the
edge of the bracket aligns with the Advantage, Vista, Encore, Eclipse, Tokheim B
alignment mark as shown in Figure 3 and Figure 4.

«
...
18
19
20
21
22
...
»

Summary of Contents for 6003-K001-V003




































































































































































Reviews:

No comments

Related manuals for 6003-K001-V003

Brand: 3M Pages: 2

Brand: Tascam Pages: 80

Brand: Tascam Pages: 2

Brand: Walker Pages: 24

Brand: BARKO LOADERS Pages: 85

Brand: UEi Pages: 5

Brand: UGO BASILE Pages: 47

Brand: UFO Pages: 16

Brand: York Pages: 16

i.Profiler plus

Brand: Zeiss Pages: 66

LED PowerBank 48

Brand: SHOWTEC Pages: 12

INTRAmatic 31 ES

Brand: KaVo Pages: 52

Brand: Aquamatic Pages: 8

Brand: Cole Parmer Pages: 28

Brand: Hammer Pages: 55

GYRONETICS E-Series

Brand: gorilla sports Pages: 22

Brand: Ecco Pages: 9

NHL Tree 23136LO

Brand: GE Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands