NCR 6003-K001-V003 Installation Instructions Manual Download Page 154 | Manualshive

Page: 154 / 163

background image

140

Figure 254

24)

Stow excess cable loops behind the APC module and above the printer. See Figure
256 below.

Figure 255

25)

Repeat steps 15) – 16) and 19) – 24) (mounting, and routing & placement of printer
cables and printer ground wire) for the printer located on the B-Side of the
dispenser using the remaining provided cable ties (006-8616073) and one more
provided cable clamp (006-8611458).

Note: On the B-Side, the printer ground wire does not have to be routed up and over
the inner top of the dispenser since the heater is on the opposite A-Side. So, for the B-

«
...
152
153
154
155
156
...
»

Summary of Contents for 6003-K001-V003




































































































































































Reviews:

No comments

Related manuals for 6003-K001-V003

Brand: MacDon Pages: 84

Brand: MacDon Pages: 89

Brand: Patton electronics Pages: 18

Brand: Farmet Pages: 102

Brand: EuroLite Pages: 28

Brand: Keithley Pages: 79

Brand: Kayakpro Pages: 17

Brand: Yoshitake Pages: 11

Brand: PASCO Pages: 30

Brand: uniprox Pages: 3

Brand: VelociRAX Pages: 4

Brand: ABM Pages: 17

Brand: Vaillant Pages: 76

Brand: H2flow Pages: 2

Brand: V-TAC Pages: 27

Brand: Yacht Sentinel Pages: 32

Brand: X-FLOC Pages: 35

univers N UC21LH1

Brand: hager Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands