manualshive.com logo in svg

NANOTEC PD4-C5918M4204-E-01, Manual

Share
Download
NANOTEC PD4-C5918M4204-E-01 Manual Download Page 33

Manual PD4-C (USB)

8 General concepts

Version: 1.4.1 / 22.07.2016 / FIR-v1626

33

Fault

If an error should occur, the motor is braked as stored in object 605E

h

.

Value in object 605E

h

Description

-32768 to -1

Reserved

0

Immediate stop with short-circuit braking

1

Braking with "slow down ramp" (deceleration depending on
operating mode)

2

Braking with "quick stop ramp" (deceleration depending on operating
mode)

3 to 32767

Reserved

Contouring Error

If a contouring error should occur, the motor is braked as stored in object 3700

h

.

Value

Description

-32768 to -1

Reserved

0

Immediate stop with short-circuit braking

1

Braking with "slow down ramp" (deceleration depending on operating mode)

2

Braking with "quick stop ramp" (deceleration depending on operating mode)

3 to 32767

Reserved

To deactivate the check for the contouring error, set the object 6065

h

 to the value "-1" (FFFFFFFF

h

).

8.2 User-defined units

8.2.1 Overview

Settings

The motor controller supports the possibility of setting user-defined units. In this way, the
corresponding parameters can be set and read out directly in degrees, mm, etc.

Pole pair count compensation

Differences in the pole pair counts of motors can be compensated. For this purpose, the value in object
2060

h

 must be set to "1". Then the pole pair count automatically enters the subsequent computation so

that different motors can be operated on the motor controller without requiring a new configuration.

Factor

There is a factor for the units velocity, acceleration and jerk. It gets either multiplied by the input value
or divided by the output value.

Internal value

Input value

Output value

x factor 

/ factor 

8.2.2 Computation formulas for user units

Gear ratio

The gear ratio is calculated from the motor revolutions (6091

h

:1

h

 (Motor Revolutions)) per shaft

revolution (6091

h

:2

h

 (Shaft Revolutions)) as follows:

Summary of Contents for PD4-C5918M4204-E-01






































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands