Nakayama BS2000, User Manual

Page: 6 / 34

EN
6
WWW.NAKAYAMATOOLS.COM
Product Features
The numbering of the components shown refers to the representation of the power tool in page 1.
①Blade-Fixed ② Blade-Moving ③ The lock-off button ④ On/Off switch ⑤ The locking retractors ⑥ Charging socket ⑦ Charging light
Charging the Battery
Warning! Always push the lock-off button ③ to “OFF” position.
Do not use other battery chargers. The supplied battery charger is designed for Lithium-ion battery in your machine.
Observe correct mains voltage: The voltage of the power source must agree with the voltage specified on the nameplate of the unit. Equipment marked with
230 V can also be connected to 220 V or 240 V. The Li-ion battery is protected against deep discharging by the “Electronic Cell Protection”. When the battery
is empty, the machine is switched off by means of a protective circuit: The inserted tool no longer rotates.
WARNING: Do not continue to press the On/Off switch after the machine has been automatically switched off. The battery can be damage.
The battery is supplied partially charged. To ensure full capacity of the battery, completely charge the battery in the battery charger before using your power
tool for the first time.
A battery that is new or has not been used for a longer period does not develop its full capacity until after approx. 5 charging/discharging cycles.
When the machine can not rotate while the On/Off switch is pressed, then the battery has no enough capacity and should be charged.
Plug the mains plug of the adaptor 9 into a socket outlet and the adaptor plug 8 into the socket 6. At this time, the battery charge-control indicator 7 lights up
red. The battery charge-control indicator indicates the charging progress. The indicator lights up red during the charge procedure. The battery is completely
charged when the indicator lights up green.
Disconnect the battery charger from the mains supply when not using it for longer periods.
Protect the battery charger against moisture!
Operation
NOTE: Remove the blade guard first before operating the machine.
Switching On and Off
To start the machine, remove the blade guard first and then push the lock-off button ③ to “ON” position, pull the locking retractors ⑤ backward, then the
moving blade ② will move back until to the fully open position. Press the On/Off switch ④ at the same time. When the machine is running, maintain the
On/Off switch state. The moving blade will go forward until to the fully close position, and then stop.
To switch off the machine, release the On/Off switch ④, Simultaneously do not release the locking retractors ⑤. The moving blade will move back until to
the fully open position, and then stop.
Maintenance and Service
Maintenance and Cleaning
Warning! Always push the lock-off button ③ to “OFF” position.
For safe and proper working, always keep the machine clean.
Always wear protective gloves when using, adjusting or cleaning the machine.
Regularly check for obvious defects such as loose fixings, and worn or damaged components.
Changing the Moving Blade (Page 1)
STEP 1: Using a 5 mm hex wrench ⑩ to loose the blade screw 11 which secures the blades. Remove the bush 12.
Remove the moving blade ② as shown.
Be careful not to allow any foreign matter to become attached to the blade gear and do not damage it. (Must make the moving blade to occupy opens or
partly opens the condition.)
STEP 2: Insert the moving blade ② to fit the screw hole as shown.
Refit the bush 12. Ensure the bush 12 is located through fixed blade and moving blade. Refit the blade screw 11 and tighten it by using a 5 mm hex wrench
⑩. Do not over-tighten.
After Pruning/Storage
Warning! Always push the lock-off button ③ to “OFF” position.
Always wear protective gloves when using, adjusting or cleaning the machine.
Clean the exterior of the machine thoroughly using a soft brush and cloth. Do not use water, solvents or polishes. Remove all debris.
Always lubricate the cutting blade with protective spray before storage.
Operate the machine and make the moving blade to fully close position. Fit the blade guard. Store the machine in a secure, dry place out of the reach of
children. Do not place other objects on top of the machine.