MUTOH ValueJet VJ-1624WX Operation Manual Download | Manualshive

Page: 335 / 358

background image

VJ-1624X/1624WX/1924WX OPERATION MANUAL

7 Troubleshooting

7.2 Error messages

335

7.2.2

Message type error display and remedies

This section describes message type errors and remedies.
Message type errors are displayed when certain failures occur during printer operation.
If a message type error occurs, the printer may display the following error messages on Operation panel
and stop operation.
If the printer stops operating, solve the error so that the printer restarts.

NOTE

When an error occurs in the color measuring mode (numbers 26 to 37 below), clear the error and
then press the [Cancel] key more than two seconds to solve the message type error.

No.

Display

Description

Remedy

Reference

1

Cover Open

Front cover is open.

Close Front cover.

3.4 Loading media

2

Mainte.CoverL Open

Left Maintenance cover is
open.

Close Maintenance cover.

2.1 Names of parts

and functions

3

Mainte.CoverR Open

Right Maintenance cover is
open.

Close Maintenance cover.

2.1 Names of parts

and functions

4

Lower the lever

Media loading lever is raised. Lower Media loading lever.

2.1 Names of parts

and functions

5

Lever Up

The media is not loaded.

Load the media.

3.4 Loading media

6

Undefined Media

Media detection has failed.
(Stops operation)

Reload the media.

3.4 Loading media

7

Media Slant

Media is fed obliquely.
(Stops operation)

Reload the media.

3.4 Loading media

8

Media Cut Error

The media was not cut.
(Stops operation)

Reload the media.

3.4 Loading media

9

End Of Roll

Roll media has run out.
(Stops operation)

Load a new roll media.

6.1.2 Replacing

10

Detach instrument

Spectrophotometer is
installed when the colors are
not being measured.
(VJ-1624X only)

Remove Spectrophotometer
(SPECTROVUE VM-10).

Spectrophotometer
(VJ-1624X only)

11

[****] Ink Low

The remaining amount of ink
is low.
(Continues operation)

Replace with a new S/C card
and Ink cartridge.

6.1.1 Replacing Ink

12

[****] InkEnd

Ink has run out.
(Stops operation)

Replace with a new S/C card
and Ink cartridge.

6.1.1 Replacing Ink

13

[****] Check Ink

Ink cartridges/Ink packs
cannot be recognized
correctly.

•Insert Ink cartridge/Ink pack
adapter again.
•Contact your local MUTOH
dealer.

6.1.1 Replacing Ink

14

[****] S/C ReadErr

IC chip cannot be read.

Insert Ink cartridge again. If
IC chip still cannot be read,
insert a new Ink cartridge.

6.1.1 Replacing Ink

«
...
333
334
335
336
337
...
»

Summary of Contents for ValueJet VJ-1624WX







































































































































































































































































































































































Reviews:

No comments

Related manuals for ValueJet VJ-1624WX

Brand: JCM Pages: 70

Brand: LabelTac Pages: 15

Brand: Oki Pages: 48

Brand: Oki Pages: 65

Brand: Oki Pages: 44

Brand: Oki Pages: 36

Brand: OHAUS Pages: 28

SuperScript 610

Brand: NEC Pages: 105

Brand: UEi Pages: 4

Brand: idp Pages: 48

Brand: Lexmark Pages: 142

Brand: Tally Pages: 174

Brand: IBM Pages: 128

PIXMA MG2220 Series

Brand: Canon Pages: 4

Brand: Canon Pages: 16

Brand: Canon Pages: 28

Brand: Canon Pages: 20

PIXMA E3300 Series

Brand: Canon Pages: 64

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands