MUTOH ValueJet VJ-1624WX Operation Manual Download

Page: 55 / 358

VJ-1624X/1624WX/1924WX OPERATION MANUAL

Before using

3.3 Filling ink

•

When head cleaning is complete, "Wash retry? No" is displayed on Operation panel.

3. Select whether to perform cleaning of the ink path before the initial ink charge.

NOTE

• Cleaning may be required depending on the ink type to be set.

• To perform head cleaning, make sure to use the cleaning liquid that matches the ink.

a. When cleaning is required, press the [+] key or [-] key to select "Yes".

b. When cleaning is not required, proceed to the step 8.

4. Press the [Enter] key on Operation panel.

•

"Insert CleaningCart." is displayed on Operation panel.

5. Take out Cleaning cartridges (4 pieces) from the bags.

Summary of Contents for ValueJet VJ-1624WX







































































































































































































































































































































































Search results

Summary of Contents for ValueJet VJ-1624WX

Reviews:

Related manuals for ValueJet VJ-1624WX

Brands by name

Popular brands

MUTOH ValueJet VJ-1624WX, Operation Manual

Search results

Summary of Contents for ValueJet VJ-1624WX

Reviews:

Related manuals for ValueJet VJ-1624WX

Brands by name

Popular brands