MUTOH ValueJet VJ-1624WX Operation Manual Download

Page: 302 / 358

6 Maintenance

VJ-1624X/1624WX/1924WX OPERATION MANUAL

302

6.2 Cleaning the printer

4. Press the [Cleaning] key on Operation panel for more than two seconds.

•

Head cleaning starts.

•

"Cleaning **%" is displayed on Operation panel.

•

After Head cleaning is complete, Operation panel shifts to Normal.

NOTE

• For VJ-1624WX/1924WX, to perform head cleaning during printing while the head height is set to

High, make sure to do the following.

• When "Change Head Gap Low" is displayed on Operation panel, set the head height to Low.

• After head cleaning is complete, "Change Head Gap High" is displayed on Operatino panel. Set

the head height to High. After changing the setting, printing starts.

4.2.5 Head height adjustment

• For VJ-1624X, auto cleaning can be performed regardless of the head height.

• If blurs or lacking parts in printed media do not disappear with one time of Head cleaning, perform

Strong cleaning.

• If blurs or lacking parts in printed media do not disappear with several times of Head cleaning, refer

7 Troubleshooting

, and take appropriate measures.

Summary of Contents for ValueJet VJ-1624WX







































































































































































































































































































































































Search results

Summary of Contents for ValueJet VJ-1624WX

Reviews:

Related manuals for ValueJet VJ-1624WX

Brands by name

Popular brands

MUTOH ValueJet VJ-1624WX, Operation Manual

Search results

Summary of Contents for ValueJet VJ-1624WX

Reviews:

Related manuals for ValueJet VJ-1624WX

Brands by name

Popular brands