MUTOH ValueJet VJ-1624WX Operation Manual Download

Page: 227 / 358

VJ-1624X/1624WX/1924WX OPERATION MANUAL

5 Panel setup menu

5.1 Setup menu

227

5.1.2

Spitting menu

Sets up the spitting operation while printing.

NOTE

• When Spitting is set to "Off", Nozzles will become easily clogged because spitting is not

performed. In such a case, print quality cannot be guaranteed.

• When the spitting setting is "On Media", the maximum printable media width becomes 16mm

shorter.
Therefore, the side margins become the value that you have set in Side Margin menu +8mm.

• The right side margin will be the following sum depending on the setting.

Y of Origin menu + 8mm (when the spitting is set to On Media) + Value set in Side Margin menu.

1. Print starting position
2. Media feed direction

X (media feeding distance)
Y (print head transferring distance)
a (0mm/8mm: Spitting setting is ON, Off/On Media)
b (5mm to 25mm: Side margin setting)

5.1.3 Side Margin menu

5.1.8 Origin menu

Summary of Contents for ValueJet VJ-1624WX







































































































































































































































































































































































Search results

Summary of Contents for ValueJet VJ-1624WX

Reviews:

Related manuals for ValueJet VJ-1624WX

Brands by name

Popular brands

MUTOH ValueJet VJ-1624WX, Operation Manual

Search results

Summary of Contents for ValueJet VJ-1624WX

Reviews:

Related manuals for ValueJet VJ-1624WX

Brands by name

Popular brands