MUTOH ValueJet VJ-1624WX Operation Manual Download

Page: 84 / 358

Before using

VJ-1624X/1624WX/1924WX OPERATION MANUAL

3.4 Loading media

5. Pull the roll media out about 1 m from the front Media feed slot which is located inside of Front

cover.

6. Rewind the roll media a little by rolling Flange on Roll media holder while holding the edge of the

media, and eliminate any slack or slant.

NOTE

• If you set the roll media free while rewinding, the roll media may fall out from Media feed slot and

fall toward the back of the printer.

• Confirm that the right edge of the roll media does not go beyond the loading mark.

If it does, it may affect print quality.

No.

Name

Roll media

Media feed slot

No.

Name

Roll media

Media loading mark

Summary of Contents for ValueJet VJ-1624WX







































































































































































































































































































































































Search results

Summary of Contents for ValueJet VJ-1624WX

Reviews:

Related manuals for ValueJet VJ-1624WX

Brands by name

Popular brands

MUTOH ValueJet VJ-1624WX, Operation Manual

Search results

Summary of Contents for ValueJet VJ-1624WX

Reviews:

Related manuals for ValueJet VJ-1624WX

Brands by name

Popular brands