MUTOH ValueJet VJ-1624WX Operation Manual Download

Page: 232 / 358

5 Panel setup menu

VJ-1624X/1624WX/1924WX OPERATION MANUAL

232

5.1 Setup menu

5.1.5

Media Width menu

Specifies the media width between the loading mark and the left end of the media if media detection is
not performed during media initialization.

(1) Media Width menu

Displays the detected media width if media detection is performed during media initialization.

(2) MediaWidth menu

For media detection settings, refer to the following.

5.1.4 Media Initial menu

NOTE

• When the media is loaded as shown in the illustration and not using media detection, the printer

may print on between the right edge of Platen and center of the media. If this happens, adjust the
print starting position in Origin menu.

5.1.8 Origin menu

No.

Name

Roll media

Media width (when not using media detection)

Media loading mark

Platen

Summary of Contents for ValueJet VJ-1624WX







































































































































































































































































































































































Search results

Summary of Contents for ValueJet VJ-1624WX

Reviews:

Related manuals for ValueJet VJ-1624WX

Brands by name

Popular brands

MUTOH ValueJet VJ-1624WX, Operation Manual

Search results

Summary of Contents for ValueJet VJ-1624WX

Reviews:

Related manuals for ValueJet VJ-1624WX

Brands by name

Popular brands