MUTOH ValueJet VJ-1624WX Operation Manual Download | Manualshive

Page: 30 / 358

background image

2 Product overview

VJ-1624X/1624WX/1924WX OPERATION MANUAL

30

2.1 Names of parts and functions

2.1.2

Rear section

No.

Name

Function

1

Roll media holder

Load the roll media.
Equipped with Flanges to attach the roll media and Fixing levers to fix Roll media
holders.

2

Media feed slot

Used for feeding media.

3

Ink cartridge slot

Insert Ink cartridges.

4

Media guide

Used to feed the media smoothly when loading or printing on the media.
• Heater (Pre-heater) to dry ink is installed inside VJ-1624X.
• VJ-1624WX/1924WX is not equipped with Heaters.

5

AC inlet

Used for connecting the power cord set.

6

Network interface cable
connector

Connects a network interface cable.

7

Waste fluid valve

Open/close when discharging the waste fluid from Waste fluid tank.
It is normally closed.

2

7

1

1

VJ-1624X

5

6

4

3

VJ-1624WX/1924WX

6

5

«
...
28
29
30
31
32
...
»

Summary of Contents for ValueJet VJ-1624WX







































































































































































































































































































































































Reviews:

No comments

Related manuals for ValueJet VJ-1624WX

Pixma G1000 series

Brand: Canon Pages: 2

Pixma G1000 series

Brand: Canon Pages: 80

ML-2240 - 23 Ppm Mono Laser Printer

Brand: Samsung Pages: 16

ML 2510 - B/W Laser Printer

Brand: Samsung Pages: 170

Brand: Xerox Pages: 114

Brand: Eazao Pages: 50

Brand: Roland Pages: 44

wematter Atmosphere

Brand: 3D Systems Pages: 11

Brand: U-Line Pages: 33

Brand: Thermotron Pages: 10

Brand: IBM Pages: 16

Brand: Felix Storch Pages: 35

DSA-3100P - B/W Thermal Line Printer

Brand: D-Link Pages: 8

imageCLASS LBP325dn

Brand: Canon Pages: 36

imageCLASS LBP161dn+

Brand: Canon Pages: 24

ImageCLASS LBP720 Series

Brand: Canon Pages: 20

imageCLASS LBP6300dn

Brand: Canon Pages: 2

imageCLASS LBP6780dn

Brand: Canon Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands