MUTOH ValueJet VJ-1624WX Operation Manual Download

Page: 153 / 358

VJ-1624X/1624WX/1924WX OPERATION MANUAL

Before using

3.6 Print quality adjustment

153

NOTE

• For VJ-1624X, “6” represents the current setting value.

• For VJ-1624WX/1924WX, “11” represents the current setting value.

• When the line is aligned, the bold line on its left side does not have a white vertical line in the

middle.

•

“Pattern A: 6” (“Pattern A: 11” for VJ-1624WX/1924WX. Refer to the chart below for *.) is
displayed on Operation panel.

5. Press the [+] key or [-] key on Operation panel to enter the number that you selected in Step 4.

NOTE

• When you press the [Cancel] key on Operation panel, the display returns to “Adj.3:

RoughPatternA”.

6. Press the [Enter] key on Operation panel.

•

Determines the setting.

•

“Adj.3: RoughPatternA” is displayed on Operation panel.

Summary of Contents for ValueJet VJ-1624WX







































































































































































































































































































































































Search results

Summary of Contents for ValueJet VJ-1624WX

Reviews:

Related manuals for ValueJet VJ-1624WX

Brands by name

Popular brands

MUTOH ValueJet VJ-1624WX, Operation Manual

Search results

Summary of Contents for ValueJet VJ-1624WX

Reviews:

Related manuals for ValueJet VJ-1624WX

Brands by name

Popular brands