MUTOH ValueJet VJ-1624WX Operation Manual Download

Page: 198 / 358

4 Handling the printer

VJ-1624X/1624WX/1924WX OPERATION MANUAL

198

4.4 Operating from Operation panel

4.4.8

Normal Display while Printing

The remaining length and remaining time to complete the currently printing data can be displayed by an
easy operation.

NOTE

• The values displayed in this function are just standard values, not guarantee the accuracy.

• If the print data includes no length data, all information will be displayed as "0".

• To check more detailed information of currently printing data, please refer to the below.

4.4.5.2 Settings that can be changed or confirmed while printing

• To check the information of printed data, please refer to the below.

5.8 Job Status Menu

Follow the procedures below to display the information.

1. Check if the printer is printing a data.

2. Press [-] key on the operation panel to display [Print Remain].

• The remaining length of data currently printing will be displayed.

TIP

• When the length display setting is set to inch, the length will be displayed in inch.

5.7.3 Length menu

• The [+] key on the operation panel also can switch the display. In that case, [Remain Time] (Step

3) will be displayed first.

㧼㨞㨕㨚㨠ޓ㧾㨑㨙㨍㨕㨚ޓޓ㨤㨤㨤㧚㨤㨙

Summary of Contents for ValueJet VJ-1624WX







































































































































































































































































































































































Search results

Summary of Contents for ValueJet VJ-1624WX

Reviews:

Related manuals for ValueJet VJ-1624WX

Brands by name

Popular brands

MUTOH ValueJet VJ-1624WX, Operation Manual

Search results

Summary of Contents for ValueJet VJ-1624WX

Reviews:

Related manuals for ValueJet VJ-1624WX

Brands by name

Popular brands