MUTOH ValueJet VJ-1624WX Operation Manual Download

Page: 194 / 358

4 Handling the printer

VJ-1624X/1624WX/1924WX OPERATION MANUAL

194

4.4 Operating from Operation panel

4.4.5

Changing and confirming settings while printing

While the printer is operating, you can change or confirm settings for the Panel setup menu.

4.4.5.1

Procedure for changing and confirming settings while printing

Follow the procedure below to change or confirm settings for the Panel setup menu.

1. Confirm that the printer is in one of the following conditions.

•

Receiving data

•

Analyzing data

•

Printing

2. Press the [Menu] key on Operation panel.

•

The following will be displayed on Operation panel.
VJ-1624X: Menu1: Temperature
VJ-1624WX/1924WX: "Menu1: PF Micro Adj."

3. Press the [+] key or [–] key to change or confirm settings.

NOTE

For the setting items whose settings can be changed or confirmed, refer to

4.4.5.2 Settings that

can be changed or confirmed while printing

Summary of Contents for ValueJet VJ-1624WX







































































































































































































































































































































































Search results

Summary of Contents for ValueJet VJ-1624WX

Reviews:

Related manuals for ValueJet VJ-1624WX

Brands by name

Popular brands

MUTOH ValueJet VJ-1624WX, Operation Manual

Search results

Summary of Contents for ValueJet VJ-1624WX

Reviews:

Related manuals for ValueJet VJ-1624WX

Brands by name

Popular brands