MUTOH ValueJet VJ-1624WX Operation Manual Download

Page: 230 / 358

5 Panel setup menu

VJ-1624X/1624WX/1924WX OPERATION MANUAL

230

5.1 Setup menu

5.1.3

Side Margin menu

Set up the right and left margins (side margins) while printing.

NOTE

• When the Spitting menu is set to "On Media", the maximum printable media width becomes 16mm

shorter.
Therefore, the side margins become the value that you have set in Side Margin menu +8mm.

5.1.1.1.9 User Copy menu

• The right side margin will be the following sum depending on the setting.

Y of Origin menu + 8mm (when the spitting is set to On Media) + Value set in Side Margin menu.

1. Print starting position
2. Media feed direction

X (media feeding distance)
Y (print head transferring distance)
a (0mm/8mm: Spitting setting is ON, Off/On Media)
b (5mm to 25mm: Side margin setting)

5.1.1.1.9 User Copy menu

5.1.8 Origin menu

Setup item

Setting

Description

Side Margin

<5mm> to 25mm

Set the side margins.

—

• [Enter] key: saves the setting and shifts to the previous

menu.

• [Cancel] key: cancels the setting and shifts to the previous

menu.

5.1 Setup menu

Summary of Contents for ValueJet VJ-1624WX







































































































































































































































































































































































Search results

Summary of Contents for ValueJet VJ-1624WX

Reviews:

Related manuals for ValueJet VJ-1624WX

Brands by name

Popular brands

MUTOH ValueJet VJ-1624WX, Operation Manual

Search results

Summary of Contents for ValueJet VJ-1624WX

Reviews:

Related manuals for ValueJet VJ-1624WX

Brands by name

Popular brands