MUTOH ValueJet VJ-1624WX Operation Manual Download

Page: 226 / 358

5 Panel setup menu

VJ-1624X/1624WX/1924WX OPERATION MANUAL

226

5.1 Setup menu

5.1.1.1.9

User Copy menu

Collectively copies the setting values of the user type currently selected to a different user type. The
following setting values are copied.

•

Print mode

•

Effect

•

Adjustment value for the adjustment print

•

Feed compensation (initial adjustment printing length, initial adjustment value, micro
adjustment value)

•

Pre-heater/Platen/Dryer

•

Vacuum Fan

•

Media Thickness

Setup item

Setting

Description

User Copy

<1> to 30, ALL

When user type is set to 1:
<2> to 30, ALL

• The setting values of the current user type are copied to the

selected user type.

• When you have selected ALL, the setting values of the

current user type are copied to the all other user types.

—

• [Enter] key: copies the settings and shifts to the previous

menu.

• [Cancel] key: shifts to the previous menu without copying

the settings.

5.1.1.1 User Type advanced setup menu

Summary of Contents for ValueJet VJ-1624WX







































































































































































































































































































































































Search results

Summary of Contents for ValueJet VJ-1624WX

Reviews:

Related manuals for ValueJet VJ-1624WX

Brands by name

Popular brands

MUTOH ValueJet VJ-1624WX, Operation Manual

Search results

Summary of Contents for ValueJet VJ-1624WX

Reviews:

Related manuals for ValueJet VJ-1624WX

Brands by name

Popular brands