MUTOH ValueJet VJ-1624WX Operation Manual Download | Manualshive

Page: 213 / 358

background image

VJ-1624X/1624WX/1924WX OPERATION MANUAL

5 Panel setup menu

5.1 Setup menu

213

5.1.1

User Type menu

Select the user type setting for printing.

5.1.1.1

User Type advanced setup menu

Various settings on the user type settings are configured.
In User Type menu, 30 different settings can be set as Type 1 to 30 for the following printing operation.

NOTE

• If media other than recommended one is used, the following problems may occur.

• Media detection error

• Slant, torn, and wrinkle of media

• Media jams

• Favorable print quality cannot be obtained due to blots, blurs or dirt of ink.

• End detection of roll media cannot be performed, etc.

The problems caused by the use of the media other than recommended one will not be covered by
the warranty and repair expenses will be paid by the customer.
For details, contact your local MUTOH dealer.

Setup item

Setting

Description

User Type

Type 1

Sets the user type setting for printing.
It is possible to set 30 different user settings as "Type 1 to 30"
for printing.
• [Enter] key: shifts to the sub menu.

5.1.1.1 User Type advanced setup menu

Type 2

…

Type 29

Type 30

—

• [Cancel] key: saves the setting and shifts to the previous

menu.

5.1 Setup menu

«
...
211
212
213
214
215
...
»

Summary of Contents for ValueJet VJ-1624WX







































































































































































































































































































































































Reviews:

No comments

Related manuals for ValueJet VJ-1624WX

Brand: WaxJet Pages: 131

Brand: Radio Shack Pages: 42

Brand: Xerox Pages: 29

Brand: Felix Storch Pages: 46

Brand: Avery Dennison Pages: 2

DocuPrint C3300 DX

Brand: Xerox Pages: 200

Brand: Z Corporation Pages: 12

Brand: Wasp Pages: 46

Brand: QMS Pages: 188

Brand: Sinfonia Technology Pages: 41

Brand: WOOSIM Pages: 56

21Z0180 - C 935hdn Color Laser Printer

Brand: Lexmark Pages: 2

1100 Color Jetprinter

Brand: Lexmark Pages: 77

Brand: Sony Pages: 8

Brand: Sony Pages: 2

Brand: Sony Pages: 2

Brand: Sony Pages: 65

Brand: Sony Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands