MTS Systems R Series V Operation Manual Download Page 19

Page: 19 / 38

Temposonics

R-Series

EtherNet/IP™

Operation Manual

I 19 I

4.7 Frequently ordered accessories

Position magnets

(0.79)

(1.69)

(0.55)

22.1 (0.87)

40 (1.57)

18°

25.3 (1)

40 (1.58)

18°

57 (2.24)

(0.55)

13.3 (0.51)

25.3 (1)

49 (1.93)

17.2 (0.67)

(0.94)

18°

(0.79)

(1.69)

40 (1.57)

25.3 (1)

18°

40 (1.57)

25.3 (1)

(0.79)

(1.65)

15.2

(0.6)

16.6 (0.63)

Magnet slider S, joint at top

Part no. 252 182

Magnet slider V, joint at front

Part no. 252 184

Magnet slider N

longer ball-joint arm

Part no. 252 183

Magnet slider G, backlash free

Part no. 253 421

Material: GRP, magnet hard ferrite

Weight: Approx. 35 g

Operating temperature:

−40…+75 °C (−40…+167 °F)

Material: GRP, magnet hard ferrite

Weight: Approx. 35 g

Operating temperature:

−40…+75 °C (−40…+167 °F)

Material: GRP, magnet hard ferrite

Weight: Approx. 35 g

Operating temperature:

−40…+75 °C (−40…+167 °F)

Material: GRP, magnet hard ferrite

Weight: Approx. 25 g

Operating temperature:

−40…+75 °C (−40…+167 °F)

Position magnets

Ø 32.8

(Ø 1.29)

Ø 23.8

(Ø 0.94)

Ø 13.5

(Ø 0.53)

Ø 4.3

(Ø 0.17)

60°

140°

3 (0.12)

7.9

(0.31)

Ø 4.5 (Ø 0.18)

Ø 63.5

(Ø 2.5)
Ø 42

(Ø 1.65)

Ø 16

(Ø 0.63)

97°

30°

9.5

(0.37)

Ø 32.8

(Ø 1.29)

Ø 23.8

(Ø 0.94)

Ø 13.5

(Ø 0.53)

Ø 4.3

(Ø 0.17)

7.9

(0.31)

Ø 25.4

(Ø 1)

Ø 13.5

(Ø 0.53)

7.9

(0.31)

U-magnet OD33

Part no. 251 416-2

U-magnet OD63.5

Part no. 201 553

Ring magnet OD33

Part no. 201 542-2

Ring magnet OD25.4

Part no. 400 533

Material: PA ferrite GF20

Weight: Approx. 11 g

Surface pressure: Max. 40 N/mm

Fastening torque for M4 screws: 1 Nm

Operating temperature:

−40…+105 °C (−40…+221 °F)

Material: PA 66-GF30,

magnets compound-fi lled

Weight: Approx.

26 g

Surface pressure: 20 N/mm

Fastening torque for M4 screws: 1 Nm

Operating temperature:

−40…+75 °C (−40…+167 °F)

Material: PA ferrite GF20

Weight: Approx. 14 g

Surface pressure: Max. 40 N/mm

Fastening torque for M4 screws: 1 Nm

Operating temperature:

−40…+105 °C (−40…+221 °F)

Material: PA ferrite

Weight: Approx. 10 g

Surface pressure: Max. 40 N/mm

Operating temperature:

−40…+105 °C (−40…+221 °F)

Position magnets

Magnet spacer

O-ring

Ø 19.8

(Ø 0.78)

Ø 30.5

(Ø 1.2)

7.6

(0.3)

19.5 (0.77)

1.5 (0.06)

33 (1.3)

(0.55)

20.5 (0.81)

14.9 (0.59)

8 ± 2 (0.31 ± 0.08)

Distance to sensor element

Ø 4.3

(Ø 0.17)

Ø 14.3

(Ø 0.56)

Ø 23.8

(Ø 0.94)

Ø 31.8

(Ø 1.25)

Ø 4.3

(Ø 0.17)

3.2

(0.13)

Ø 14.3

Ø 23.8

Ø 31.8

Ø 4.3

3.2

Ø 15.3

(Ø 0.6)

Ø 2.2

(Ø 0.09)

Ring magnet

Part no. 402 316

Block magnet L

Part no. 403 448

Magnet spacer

Part no. 400 633

O-ring for threaded ﬂ ange

M18×1.5-6g

Part no. 401 133

Material: PA ferrite coated

Weight: Approx. 13 g

Surface pressure: Max. 20 N/mm

Operating temperature:

−40…+100 °C (−40…+212 °F)

Material: Hard ferrite

Weight: Approx. 20 g

Fastening torque for M4 screws: 1 Nm

Operating temperature:

−40…+75 °C (−40…+167 °F)

This magnet may infl uence the sensor

performance specifi cations for some

applications.

Material: Aluminum

Weight: Approx. 5 g

Surface pressure: Max. 20 N/mm

Fastening torque for M4 screws: 1 Nm

Material: Fluoroelastomer

Durometer: 75 ± 5 Shore A

Operating temperature:

−40…+204 °C (−40…+400 °F)

– Additional options available in our

Accessories Guide

551 444

Controlling design dimensions are in millimeters and measurements in ( ) are in inches

Summary of Contents for R Series V







































Search results

Summary of Contents for R Series V

Reviews:

Related manuals for R Series V

Brands by name

Popular brands

MTS Systems R Series V, Operation Manual

Search results

Summary of Contents for R Series V

Reviews:

Related manuals for R Series V

Brands by name

Popular brands