MTS Systems R Series V Operation Manual Download Page 21

Page: 21 / 38

Temposonics

R-Series

EtherNet/IP™

Operation Manual

I 21 I

Cables

PUR cable

Part no. 530 125

PVC cable

Part no. 530 108

Cable with M12 D-coded male

connector (4 pin), straight – M12

D-coded, male connector (4 pin),

straight

Part no. 530 064

Cable with M12 D-coded male

connector (4 pin), straight – RJ45

male connector, straight

Part no. 530 065

Material: PUR jacket; green

Features: Cat 5, highly fl exible

Cable Ø: 6.5 mm (0.26 in.)

Cross section: 2 × 2 × 0.35 mm

(22/7 AWG)

Operating temperature:

−20…+60 °C (−4…+140 °F)

Material: PVC jacket; gray

Features: Shielded, fl exible

Cable Ø: 4.9 mm (0.19 in.)

Cross section: 3 × 0.34 mm²

Operating temperature:

−30…+80 °C (−22…+176 °F)

Material: PUR jacket; green

Features: Cat 5e

Cable length: 5 m (16.4 ft)

Cable Ø: 6.5 mm (0.26 in.)

Ingress protection: IP65, IP67, IP68

(correctly fi tted)

Operating temperature:

−30…+70 °C (−22…+158 °F)

Material: PUR jacket; green

Features: Cat 5e

Cable length: 5 m (16.4 ft)

Cable Ø: 6.5 mm (0.26 in.)

Ingress protection M12 connector:

IP67 (correctly fi tted)

Ingress protection RJ45 connector:

IP20 (correctly fi tted)

Operating temperature:

−30…+70 °C (−22…+158 °F)

Cables

Programming kit

Cable with M8 female connector

(4 pin), straight – pigtail

Part no. 530 066 (5 m (16.4 ft.))

Part no. 530 096 (10 m (32.8 ft.))

Part no. 530 093 (15 m (49.2 ft.))

TempoLink smart assistant for

Temposonics

R-Series

Part no. TL-1-0-EM12

Material: PUR jacket; gray

Features: Shielded

Cable Ø: 8 mm (0.3 in.)

Operating temperature:

−40…+90 °C (−40…+194 °F)

•

Connect wirelessly via Wi-Fi enabled

device or via USB with the diagnostic

tool

•

Simple connectivity to the sensor

via 24 VDC power line

•

User friendly interface for mobile

devices and desktop computers

•

Rugged ABS plastic construction

for the industrial environment

•

See product brief “TempoLink

smart assistant” (document part no.:

551976) for further information

Controlling design dimensions are in millimeters and measurements in ( ) are in inches

Manuals & Software available at:

www.mtssensors.com

Summary of Contents for R Series V







































Search results

Summary of Contents for R Series V

Reviews:

Related manuals for R Series V

Brands by name

Popular brands

MTS Systems R Series V, Operation Manual

Search results

Summary of Contents for R Series V

Reviews:

Related manuals for R Series V

Brands by name

Popular brands