MRV Communications EM316LNXNM-OT User Manual Download Page 48

Page: 48 / 181

EM316LNXNM-OT

Management Basics

PN 1275005-100 Rev E6

• To re-start the LNXNM and reload firmware only, but not reload configuration:

fiberdriver# restart upgrade

Waiting for processes..ok

Restarting system

If the EM316LNXNM does not start after an upgrade process, the normal boot process can be interrupted
to download a valid "uImage.initrd" file from a TFTP server. See the "

Recovering from a failed 'upgrade'

command"

section in the Troubleshooting chapter.

5.5.22. LNXNM Firmware Downgrades

Before upgrading the system software, always make a backup of the current

"startup-config"

file. This backup may be used to downgrade the EM316LNXNM to this previous version of software,
if necessary.

To back up the current

startup-config

file:

fiberdriver# write file

Building configuration file...

OK, saved to startup-config

fiberdriver# tftp put 10.1.1.15 startup-config saved-startup-config

putting startup-config ...

TFTP finished!

fiberdriver#

See

"Firmware: Upgrade"

for more information.

Summary of Contents for EM316LNXNM-OT






















































































































































































Search results

Summary of Contents for EM316LNXNM-OT

Reviews:

Related manuals for EM316LNXNM-OT

Brands by name

Popular brands

MRV Communications EM316LNXNM-OT, User Manual

Search results

Summary of Contents for EM316LNXNM-OT

Reviews:

Related manuals for EM316LNXNM-OT

Brands by name

Popular brands