MRV Communications EM316LNXNM-OT User Manual Download Page 152

Page: 152 / 181

EM316LNXNM-OT

Appendix

PN 1275005-100 Rev E6

145

Command

Description

map not-to C.S.P

Enter port location

map not-to NAME

Remove the source port from that destination port

map only-to C.S.P

Enter port location

map only-to NAME

Map to a port (and clear all other mappings for
both ports)

map repeater

Set to 'repeater' setting (1 <-> 2, etc.)

map to-self

Map to itself (and clear other mappings)

map with C.S.P

(no description yet)

map with CSSPPP

Connect to ...

map with LINE

Connect to ...

map with NAME

Connect to ...

map with PORT

Connect to ...

default mapping-type

Adjust mapping type of the port, to define
mapping restrictions

mapping-type destination

This port would only be able to be mapped from
other ports

mapping-type inter-chas-link

This port would only be used for inter-chassis
links

mapping-type open

This port would be available for all types of
mappings

mapping-type source

This port would only be able to map to other ports

mapping-type source-helper

This port would only be able to map to source
ports

mapping-type unavailable

This port will not be able to be mapped

default mdi-pinout

Adjust MDI/MDI-X

mdi-pinout auto-sense

Autodetect MDI/MDI-X

mdi-pinout mdi

MDI

mdi-pinout mdix

MDI-X

default me

Restore defaults for this location only

next

Configure next element

default nominal-bit-rate

Set port custom bit-rate

nominal-bit-rate <0-4294967294>

Set port custom bit-rate

[default|no] oam

enable OAM management

[no] pager

Pause scrolling when screen is full

default path-transmitters

Restore The transmitter on each port in a data path
to default setting

path-transmitters disable-all

Set The transmitter on each port in a data path to
"disable-all"

path-transmitters enable-all

Set The transmitter on each port in a data path to
"enable-all"

Summary of Contents for EM316LNXNM-OT






















































































































































































Search results

Summary of Contents for EM316LNXNM-OT

Reviews:

Related manuals for EM316LNXNM-OT

Brands by name

Popular brands

MRV Communications EM316LNXNM-OT, User Manual

Search results

Summary of Contents for EM316LNXNM-OT

Reviews:

Related manuals for EM316LNXNM-OT

Brands by name

Popular brands