MRV Communications EM316LNXNM-OT User Manual Download Page 146

Page: 146 / 181

EM316LNXNM-OT

Appendix

PN 1275005-100 Rev E6

139

Command

Description

show statistics

Show port info

show traps

Show trap filter configuration

show unmapped

Show only unmapped ports

show vid-map

Show VID map for the current slot

sleep <0-10>

Pause CLI for scripting

slot C.S

A slot location

slot NAME

Configure a slot

slot S

A slot on this chassis

default storm-control broadcast

Configure flooding limit for broadcast frames
(Kfps)

storm-control broadcast <0-255>

Configure flooding limit for broadcast frames
(Kfps)

default storm-control multicast

Configure flooding limit for multicast frames
(Kfps)

storm-control multicast <0-255>

Configure flooding limit for multicast frames
(Kfps)

default storm-control unicast

Configure flooding limit for unicast frames (Kfps)

storm-control unicast <0-255>

Configure flooding limit for unicast frames (Kfps)

sync

Wait for changes to be flushed to hardware /
display

default toggle-rate

Adjust toggling rate (microseconds), Value will be
rounded to the closest HW value

toggle-rate <1-2147483647>

Adjust toggling rate (microseconds), Value will be
rounded to the closest HW value

[default|no] trap

Enable trap generation

[no] trap NAME

Enable trap generation

Configure parent element

default user-oam-1

Restore User OAM Channel 1 to default setting

user-oam-1 discard

Set User OAM Channel 1 to "discard"

user-oam-1 notSupported

Set User OAM Channel 1 to "notSupported"

user-oam-1 passthru

Set User OAM Channel 1 to "passthru"

default user-oam-2

Restore User OAM Channel 2 to default setting

user-oam-2 discard

Set User OAM Channel 2 to "discard"

user-oam-2 notSupported

Set User OAM Channel 2 to "notSupported"

user-oam-2 passthru

Set User OAM Channel 2 to "passthru"

default user-port-limit

define bandwidth (Kbps) for user-port traffic

user-port-limit <0-1000000>

define bandwidth (Kbps) for user-port traffic

default vid-map

Return VID map configuration to defaults

no vid-map <0-4095>

Remove VID map

vid-map <0-4095> <0-4095> active

VID row active

Summary of Contents for EM316LNXNM-OT






















































































































































































Search results

Summary of Contents for EM316LNXNM-OT

Reviews:

Related manuals for EM316LNXNM-OT

Brands by name

Popular brands

MRV Communications EM316LNXNM-OT, User Manual

Search results

Summary of Contents for EM316LNXNM-OT

Reviews:

Related manuals for EM316LNXNM-OT

Brands by name

Popular brands