Moxa Technologies EDS-405A User Manual Download Page 80

Page: 80 / 103

EDS-405A/408A Series User’s Manual

Featured Functions

3-65

Using Event Log

Bootup

This field shows how many times the EDS has been rebooted or cold
started.

Date

The date is updated based on how the current date is set in the “Basic
Setting” page.

Time

The time is updated based on how the current time is set in the “Basic
Setting” page.

System Startup Time The system startup time related to this event.
Events

Events that have occurred.

Events are logged in the EDS-405A/408A Event Log when the following events occur:

Cold start

Warm start

Configuration Change Activated

Power Transition from OFF to ON or from ON to OFF

Authentication Fail

Topology Changed

Master Setting is Mismatched

Port Traffic Overload

Port Link from OFF to ON or from ON to OFF

Summary of Contents for EDS-405A








































































































Search results

Summary of Contents for EDS-405A

Reviews:

Related manuals for EDS-405A

Brands by name

Popular brands

Moxa Technologies EDS-405A, User Manual

Search results

Summary of Contents for EDS-405A

Reviews:

Related manuals for EDS-405A

Brands by name

Popular brands