Moxa Technologies EDS-405A User Manual Download Page 70 | Manualshive

Page: 70 / 103

background image

EDS-405A/408A Series User’s Manual

Featured Functions

3-55

Event Types

Event Types can be divided into two basic groups:

System Events

and

Port Events

. System

Events are related to the overall function of the switch, whereas Port Events are related to the
activity of a specific port.

The EDS supports one relay output. You can configure which relay output is related to which
events. This helps administrators identify the importance of the different events.

System Event

Warning Relay output is triggered when…

Power Transition (On



Off)

EDS is powered up.

Power Transition (Off



On)

EDS is powered down.

Turbo Ring Break (Ring Master
Only)

When the EDS-405A/408A is the Master of this
Turbo Ring, and the Turbo Ring is disconnected.

NOTE

If the Turbo Ring Switch function is enabled, and the Turbo Ring DIP Switch is set to “ON”, the
Turbo Ring Break Event cannot be changed. If not, the Turbo Ring Break Event can be set by
using a web browser.

NOTE

The Turbo Ring Break Warning will be automatically enabled when the following configuration
is set:

1.

Turbo Ring DIP Switch functions are enabled.

2.

The Hardware Turbo Ring DIP Switch is set to “ON”.

3.

The Master DIP Switch is set to “ON”.

Please refer to “Configuring Basic Settings

—

Turbo Ring DIP Switch” for more details.

Port Event

Warning e-mail is sent when…

Link-on

The port is connected to another device.

Link-off

The port is disconnected (e.g., the cable is pulled
out, or the opposing device shuts down).

Traffic-Overload

The port’s traffic surpasses the Traffic-Threshold for
that port (provided this setting is Enabled).

Traffic-Threshold (%)

Enter a nonzero number if the port’s
Traffic-Overload setting is Enabled.

Traffic-Duration (sec.)

A Traffic-Overload warning is sent every

Traffic-Duration

seconds if the average

Traffic-Threshold is surpassed during that time
period.

NOTE

The

Traffic-Overload

,

Traffic-Threshold (%)

, and

Traffic-Duration (sec)

Port Event items

are related. If you Enable the Traffic-Overload event, then be sure to enter a nonzero
Traffic-Threshold percentage, as well as a Traffic-Duration between 1 and 300 seconds.

«
...
68
69
70
71
72
...
»

Summary of Contents for EDS-405A








































































































Reviews:

No comments

Related manuals for EDS-405A

Brand: Patton electronics Pages: 2

3CR860-95 - OfficeConnect Secure Router

Brand: 3Com Pages: 2

Brand: 3Com Pages: 26

SmartMedia Adapter PC Card REX-SMA01F

Brand: Ratoc Systems Pages: 75

Brand: Vanguard Pages: 4

Brand: Datasheen Pages: 25

Brand: Maxim Pages: 14

X-Pedition 2000

Brand: Enterasys Pages: 86

Brand: Fostex Pages: 20

Brand: Baldor Pages: 34

Brand: Daedalon Pages: 6

Brand: Netis Pages: 16

Brand: Aewin Technologies Pages: 86

ExpressBox2 EB2

Brand: Magma Pages: 74

Brand: Hauppauge Pages: 55

EK-FC980 GTX Classy

Brand: ekwb Pages: 2

Brand: AXIOMTEK Pages: 2

Brand: NBase Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands