Moxa Technologies EDS-405A User Manual Download Page 20

Page: 20 / 103

EDS-405A/408A Series User’s Manual

Featured Functions

3-5

The following table shows additional configuration examples:

Allowable Hosts

Input format

Any host

Disable

192.168.1.120 192.168.1.120

255.255.255.255

192.168.1.1 to 192.168.1.254

192.168.1.0 / 255.255.255.0

192.168.0.1 to 192.168.255.254

192.168.0.0 / 255.255.0.0

192.168.1.1 to 192.168.1.126

192.168.1.0 / 255.255.255.128

192.168.1.129 to 192.168.1.254

192.168.1.128 / 255.255.255.128

Port

Port

settings are included to give the user control over Port Access, Port Transmission Speed,

Flow Control, and Port Type (MDI or MDIX). An explanation of each configuration item is given
below. (NOTE: The user interface for the EDS-408A will show 8 ports.)

Enable

Setting

Description

Factory Default

checked

Allows data transmission through the port.

unchecked

Immediately shuts off port access.

disabled

ATTENTION

If a connected device or sub-network is wreaking havoc on the rest of the network, the

Disable

option under

Advanced Settings/Port

gives the administrator a quick way to immediately shut

off access through this port.

Summary of Contents for EDS-405A








































































































Search results

Summary of Contents for EDS-405A

Reviews:

Related manuals for EDS-405A

Brands by name

Popular brands

Moxa Technologies EDS-405A, User Manual

Search results

Summary of Contents for EDS-405A

Reviews:

Related manuals for EDS-405A

Brands by name

Popular brands