Moxa Technologies EDS-405A User Manual Download Page 30

Page: 30 / 103

EDS-405A/408A Series User’s Manual

Featured Functions

3-15

System File Update—By Local Import/Export

Configuration File

To export the configuration file of this EDS, click

Export

to save it to the local host.

Log File

To export the Log file of this EDS, click

Export

and save it to the local host.

NOTE

Some operating systems will open the configuration file and log file directly in the web page. In
such cases, right click the “Export” button to save a file.

Upgrade Firmware

To import the firmware file of the EDS, click

Browse

to select the firmware file already saved on

your computer. The upgrade procedure will proceed automatically after you click

Import

Upload Configuration Data

To import the configuration file of the EDS, click

Browse

to select the configuration file already

saved on your computer. The upgrade procedure will proceed automatically after you click

Import

System File Update—By Backup Media

Auto load system configurations when system boots up

Setting

Description

Factory Default

Enable

Enables Auto load system configurations when
system boots up

Disable

Disables Auto load system configurations when
system boots up

Enable

Summary of Contents for EDS-405A








































































































Search results

Summary of Contents for EDS-405A

Reviews:

Related manuals for EDS-405A

Brands by name

Popular brands

Moxa Technologies EDS-405A, User Manual

Search results

Summary of Contents for EDS-405A

Reviews:

Related manuals for EDS-405A

Brands by name

Popular brands