Moxa Technologies EDS-405A User Manual Download Page 71 | Manualshive

Page: 71 / 103

background image

EDS-405A/408A Series User’s Manual

Featured Functions

3-56

Override Relay Warning Settings

Click the checkbox to override the relay warning setting temporarily. Releasing the relay output
will allow administrators to fix any problems with the warning condition.

Relay Warning List

Use this table to see if any relay warnings have been issued.

Using Line-Swap-Fast-Recovery

The Line-Swap Fast Recovery function, which is enabled by default, allows the EDS to return to
normal operation very quickly after devices are unplugged and then re-plugged into different ports.
The recovery time is in the order of a few milliseconds. Compare this with standard commercial
switches for which the recovery time could be in the order of several minutes. To disable the
Line-Swap Fast Recovery function, or to re-enable the function after it has already been disabled,
access either the Console utility’s

Line-Swap recovery

page, or the Web Browser interface’s

Line-Swap fast recovery

page, as shown next.

Configuring Line-Swap Fast Recovery

Enable Line-Swap-Fast-Recovery

Setting

Description

Factory Default

Enable/Disable

Select this setting to enable the
Line-Swap-Fast-Recovery function

Enable

«
...
69
70
71
72
73
...
»

Summary of Contents for EDS-405A








































































































Reviews:

No comments

Related manuals for EDS-405A

Brand: D-Link Pages: 100

Brand: D-Link Pages: 134

Brand: D-Link Pages: 187

Brand: D-Link Pages: 225

Brand: D-Link Pages: 31

Brand: D-Link Pages: 35

DES-1016D - Switch

Brand: D-Link Pages: 19

Brand: D-Link Pages: 107

AirPlusXtremeG DI-624

Brand: D-Link Pages: 5

Brand: D-Link Pages: 48

Module NI PXI-8250

Brand: National Instruments Pages: 39

Brand: Watchguard Pages: 39

PG-FlexPlus AMU-912

Brand: ADC Pages: 130

Brand: Fieldbus Specialists Pages: 39

Brand: SIIG Pages: 20

Brand: M86 Security Pages: 309

Brand: StarTech.com Pages: 9

Brand: Disc Makers Pages: 38

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands