Moxa Technologies EDS-405A User Manual Download Page 85

Page: 85 / 103

EDS-405A/408A Series User’s Manual

EDS Configurator GUI

4-4

Upgrade Firmware

Keep your Moxa EtherDevice Switch up to date with the latest firmware from Moxa. Do the
following to upgrade the firmware:

Download the updated firmware (*.rom) file from the Moxa website (www.moxa.com).

Click the switch (from the

Moxa EtherDevice Switch Configurator

window) whose

firmware you wish to upgrade to highlight it.

Click the

Upgrade Firmware

toolbar icon

, or select

Upgrade

from the

Firmware

menu.

If the switch is locked, you will be prompted to input the switch’s User Name and Password.

Click

Open

to navigate to the folder that contains the firmware upgrade file, and then click

the correct “*.rom” file (

eds.rom

in the example shown below) to select the file. Click

Open

to activate the upgrade process.

Summary of Contents for EDS-405A








































































































Search results

Summary of Contents for EDS-405A

Reviews:

Related manuals for EDS-405A

Brands by name

Popular brands

Moxa Technologies EDS-405A, User Manual

Search results

Summary of Contents for EDS-405A

Reviews:

Related manuals for EDS-405A

Brands by name

Popular brands