Motorola EX-3524 Cli Reference Manual Download Page 50 | Manualshive

Page: 50 / 617

background image

Chapter 1

| Initial Switch Configuration

Configuring Automatic Installation of Operation Code and Configuration Settings

– 50 –

Configuring Automatic Installation of Operation Code and Configuration Settings

Downloading

Operation Code

from a File Server

Automatic Operation Code Upgrade can automatically download an operation
code file when a file newer than the currently installed one is discovered on the file
server. After the file is transferred from the server and successfully written to the file
system, it is automatically set as the startup file, and the switch is rebooted.

Usage Guidelines

◆

If this feature is enabled, the switch searches the defined URL once during the
bootup sequence.

◆

FTP (port 21) and TFTP (port 69) are both supported. Note that the TCP/UDP
port bindings cannot be modified to support servers listening on non-standard
ports.

◆

The host portion of the upgrade file location URL must be a valid IPv4 IP
address. DNS host names are not recognized. Valid IP addresses consist of four
numbers, 0 to 255, separated by periods.

◆

The path to the directory must also be defined. If the file is stored in the root
directory for the FTP/TFTP service, then use the “/” to indicate this (e.g., ftp://
192.168.0.1/).

◆

The file name must not be included in the upgrade file location URL. The file
name of the code stored on the remote server must be ECS4620-28T.bix (using
lower case letters as indicated).

◆

The FTP connection is made with PASV mode enabled. PASV mode is needed to
traverse some fire walls, even if FTP traffic is not blocked. PASV mode cannot be
disabled.

◆

The switch-based search function is case-insensitive in that it will accept a file
name in upper or lower case (i.e., the switch will accept

EX3524_Op.BIX

from the

server even though

EX3524_Op.bix

was requested). However, keep in mind that

the file systems of many operating systems such as Unix and most Unix-like
systems (FreeBSD, NetBSD, OpenBSD, and most Linux distributions, etc.) are
case-sensitive, meaning that two files in the same directory,

ex3524_op.bix

and

EX3524_Op.BIX

are considered to be unique files. Thus, if the upgrade file is

stored as

EX3524_Op.BIX

(or even

Ex3524_Op.bix

) on a case-sensitive server,

then the switch (requesting

EX3524_Op.BIX

) will not be upgraded because the

server does not recognize the requested file name and the stored file name as
being equal. A notable exception in the list of case-sensitive Unix-like operating
systems is Mac OS X, which by default is case-insensitive. Please check the
documentation for your server’s operating system if you are unsure of its file
system’s behavior.

«
...
48
49
50
51
52
...
»

Summary of Contents for EX-3524










































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for EX-3524

Brand: ?omtime Pages: 62

StorTrends 1312-P

Brand: American Megatrends Pages: 2

Brand: Net to Net Technologies Pages: 4

Brand: SyChip Pages: 24

Brand: Westermo Pages: 34

ApplianceStor 15MT

Brand: Rasilient Pages: 30

Brand: PRIZM Pages: 8

Acme Packet 3900

Brand: Oracle Pages: 70

Brand: Ruckus Wireless Pages: 4

WISENET XRN-1610

Brand: Hanwha Techwin Pages: 88

Brand: Vivotek Pages: 185

Brand: Hirschmann Pages: 8

Brand: Icy Box Pages: 17

Brand: Porter-Cable Pages: 6

DHI-NVR5208-4KS2

Brand: Dahua Pages: 361

Brand: Dahua Pages: 489

cnPilot Home R200 Series

Brand: Cambium Networks Pages: 136

Brand: Cambium Networks Pages: 208

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands