MOTO GUZZI Stelvio 1200 NTX Service Station Manual Download Page 141

Page: 141 / 290

•

Place the valve guide oil seal (4) in the

head.

•

Place the lower cap (5).

•

Place the valve (6) inside the head.

•

Place the spring (3).

•

Fit the upper cap (2).

•

Place the two cotters (1) on the seats

in the valves.

•

By compressing the spring (3) with the

special tool, fit the valve cotters.

Specific tooling

10.90.72.00

Tool for valve removal and refitting

AP9100838

Tool for valve pressure plate

•

Remove the special tool

Installing the rocker arms

•

Fit the camshaft.

•

Fit the two rods.

WARNING

MAKE SURE THAT THE NOTCH ON THE DIPSTICK BODY
FACES THE ROCKING LEVER.

Stelvio 1200 NTX ABS

Engine

ENG - 141

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

Summary of Contents for Stelvio 1200 NTX



































































































































































































































































































Search results

Summary of Contents for Stelvio 1200 NTX

Reviews:

Related manuals for Stelvio 1200 NTX

Brands by name

Popular brands

MOTO GUZZI Stelvio 1200 NTX, Service Station Manual

Search results

Summary of Contents for Stelvio 1200 NTX

Reviews:

Related manuals for Stelvio 1200 NTX

Brands by name

Popular brands