manualshive.com logo in svg

MOTO GUZZI Stelvio 1200 NTX, Service Station Manual

The MOTO GUZZI Stelvio 1200 NTX is a powerful and reliable adventure bike designed to tackle any terrain. To maintain its optimal performance, it's essential to have the Service Station Manual at hand for routine maintenance. Download this comprehensive manual for free from manualshive.com, ensuring you have all the information you need at your fingertips.

Share
Download
background image

•

Disconnect both spark plug tubes.

•

Unscrew and remove the four head

cover fixing screws and collect the

sealing O-rings.

•

Remove the head cover together with

the gasket.

•

Loosen the nut (1).

•

Use a screwdriver to act on set screw

(2) until the following clearances are

obtained:

Inlet valve: 0.10 mm (0.0039 in)

Outlet valve: 0.15 mm (0.0059 in)

•

The measurement must be taken using

a special thickness gauge.

CAUTION

IF CLEARANCE IS LARGER THAN RECOMMENDED, THE
TAPPETS WILL BE NOISY. OTHERWISE, THE VALVES DO
NOT CLOSE CORRECTLY, WHICH CAN LEAD TO PROB-
LEMS SUCH AS:

•

PRESSURE DROP;

•

ENGINE OVERHEAT;

•

VALVE BURN OUT, ETC.

Braking system

Level check

Brake fluid check

•

Rest the vehicle on its stand.

•

For the front brake, turn the handlebar fully to the right.

Maintenance

Stelvio 1200 NTX ABS

MAIN - 38

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

Summary of Contents for Stelvio 1200 NTX



































































































































































































































































































Reviews:

No comments

Related manuals for Stelvio 1200 NTX

hepco & becker 6617530 01 01 Mounting Instructions preview
6617530 01 01
Brand: hepco & becker Pages: 6
R&G FI0054BK Fitting Instructions preview
FI0054BK
Brand: R&G Pages: 4
GIVI SR6110 Quick Start Manual preview
SR6110
Brand: GIVI Pages: 3
Suzuki RM250 Owner'S Service Manual preview
RM250
Brand: Suzuki Pages: 151
DAELIM ROADWIN 125 FI Manual preview
ROADWIN 125 FI
Brand: DAELIM Pages: 68
SUR-RON Light Bee Service Manual preview
Light Bee
Brand: SUR-RON Pages: 50
kellermann BL 1000 PL Installation Instructions preview
BL 1000 PL
Brand: kellermann Pages: 2
BMW Motorrad HP2 Megamoto Rider'S Manual preview
HP2 Megamoto
Brand: BMW Motorrad Pages: 146
GAS GAS TXT ROOKIE - 2006 Service Manual preview
TXT ROOKIE - 2006
Brand: GAS GAS Pages: 32
Blata Origami B1 Service Manual preview
Origami B1
Brand: Blata Pages: 17
Pacific Helmets HALOFLEX F20H User'S Information Manual preview
HALOFLEX F20H
Brand: Pacific Helmets Pages: 40
hepco & becker 611.793 00 02 Assembling Instructions preview
611.793 00 02
Brand: hepco & becker Pages: 4
JETPRIME JP MJ 008 Installation Manual preview
JP MJ 008
Brand: JETPRIME Pages: 4
Yamaha FZ6-SS Assembly Manual preview
FZ6-SS
Brand: Yamaha Pages: 26
Yamaha FZ150 Parts Catalogue preview
FZ150
Brand: Yamaha Pages: 58
Yamaha FZ-16 Assembly Manual preview
FZ-16
Brand: Yamaha Pages: 42
Yamaha FZS1000T Owner'S Manual preview
FZS1000T
Brand: Yamaha Pages: 92
Yamaha FZ6-N 2004 Service Manual preview
FZ6-N 2004
Brand: Yamaha Pages: 77

Brands by name

Popular brands

Load more brands